Description
The ball valve is used as a shut-off valve in heat supply systems, water supply systems, in steam, fuel and pneumatic systems with compressed air and neutral gases. Installation of valves of this series is possible in systems transporting liquid and gaseous media (water, oil, oils, steam, air, alcohols, glycol, etc.), non-aggressive to the valve materials. The use of ball valves as control valves is not allowed.
DNOVA double-acting rotary pneumatic actuators PA-DA and PA-SA rotary pneumatic actuators with return spring are designed to automate the process of controlling industrial valves with a maximum torque of up to 2128 Nm.
The pneumatic distributor is used to change the direction, start, and stop the flow of compressed air in a pneumatic system depending on the external control action.
The manual override with worm gear and HDM reduction gear allows manual setting of the required positioning of the shut-off element by a quarter turn, acting as an alternative to pneumatic, electric or hydraulic quarter-turn actuators. Suitable for both indoor and outdoor installation. The modular design of the manual override is intended to provide the most effective and efficient solution for the entire range of manual override tasks.
The limit switch unit is designed for visual and electrical signaling of the end positions of the shut-off element of the valve: valve, tap or butterfly valve. It is installed on top of the surface of the pneumatic drive and connected to the DIN standard drive shaft. In a sealed box, as a rule, there are two sensors that monitor the position of the drive shaft and signal in extreme positions. OMRON microswitches, inductive sensors or reed switches are used as sensors. Visual indication of the position can be seen on the body of the unit there is a 3D visual indicator RED - CLOSED and GREEN - OPEN.
The air preparation unit is designed to clean compressed air from droplet moisture and solid particles, remove condensate, automatically maintain pressure at a given level, and supply lubricant from the reservoir to the compressed air flow to the elements of the pneumatic system.
Technical parameters of the DNOVA BV3232P(2pc)-FP-T-ISO-H ball valves DN10-50 PN63, full bore coupling, stainless steel SS316, PTFE, with double-acting PA-DA pneumatic actuator, with 4V320-08 220V pneumatic distributor, with APL-210N LSU, with MON1-250-T26-ISO manual override, with AF ATU:
| Name | Meaning |
| Working pressure, bar | 63 |
| Working environment temperature, °C | from -20 to 200 |
| Application | heat supply |
| Working environment | water, air, steam, slightly aggressive environment, oils, industrial water, water-glycol solutions, petroleum products |
| Connection to the pipeline | coupling (threaded) |
| Water intake | No |
| Type of flow section | full bore |
| Control type | With pneumatic drive |
| Joining | Internal thread |
| Control | double acting pneumatic actuator |
| Availability of limit switches | There is |
| Availability of pneumatic distributor | There is |
Sketch Ball valves DNOVA BV3232P(2pc)-FP-T-ISO-H DN10-50 PN63, full bore coupling, stainless steel SS316, PTFE, with double-acting pneumatic actuator PA-DA, with pneumatic distributor 4V320-08 220V, with LSU APL-210N, with manual override MON1-250-T26-ISO, with ATU AF
Dimensions and sizes of ball valves DNOVA BV3232P(2pc)-FP-T-ISO-H DN10-50 PN63, full bore coupling, stainless steel SS316, PTFE, with double-acting pneumatic actuator PA-DA, with pneumatic distributor 4V320-08 220V, with LSU APL-210N, with manual override MON1-250-T26-ISO, with ATU AF:
| № | Part name | Material |
| 1, 6 | Body | steel 316 |
| 2, 4 | Ball seal | PTFE |
| 3 | Char | steel 316 |
| 5 | O-ring | PTFE |
| 7 | Stem | steel 316 |
| 8 | Stem seal | PTFE |
| 9 | Stem nut | steel 316 |
| 10 | Handle | stainless steel |
Sketch of parts and materials Ball valves DNOVA BV3232P(2pc)-FP-T-ISO-H DN10-50 PN63, full bore coupling, stainless steel SS316, PTFE, with double-acting pneumatic actuator PA-DA, with pneumatic distributor 4V320-08 220V, with LSU APL-210N, with manual override MON1-250-T26-ISO, with ATU AF
Table of parts and materials Ball valves DNOVA BV3232P(2pc)-FP-T-ISO-H DN10-50 PN63, full bore coupling, stainless steel SS316, PTFE, with double-acting pneumatic actuator PA-DA, with pneumatic distributor 4V320-08 220V, with LSU APL-210N, with manual override MON1-250-T26-ISO, with ATU AF:
| Item No. | Details | Materials |
| 1.6 | Frame | steel 316 |
| 2.4 | Ball seal | polytetrafluoroethylene PTFE |
| 3 | Ball | steel 316 |
| 5 | Sealing ring | polytetrafluoroethylene PTFE |
| 7 | Stock | steel 316 |
| 8 | Rod seal | VITON |
| 9 | Stem nut | steel 316 |
Technical parameters of the pneumatic drive DNOVA
| Name | Meaning |
| Design | double acting |
| Working pressure, bar | 6 |
| Working environment | filtered compressed air or non-aggressive gases, oils |
| Availability of manual backup | steering wheel |
Sketch of the dimensions and sizes of the pneumatic drive DNOVA
Dimensions and sizes of the pneumatic drive DNOVA:
| Drive model | DA-052 | DA-065 |
| G, mm | 15 | 15 |
| Mmm | 80 | 80 |
| N, mm | 30 | 30 |
| F0, mm | 34 | 34 |
| R, mm | 20 | 20 |
| B1, mm | 153 | 174 |
| C, mm | 30 | 36 |
| E, mm | 72 | 89 |
| J | 4-M5x8 | 4-M6x10 |
| TO | 4-M6x10 | 4-M8x12 |
| F, mm | 26 | 26 |
| A1, mm | 108 | 125 |
| D, mm | 41 | 46 |
| L | 11x11 | 14x14 |
| H | F03 | F05 |
| I | F05 | F07 |
Sketch of parts and materials of pneumatic drive DNOVA
Table of parts and materials of pneumatic drive DNOVA:
| No. | Name | Quantity | Material | Coating |
| 1 | Frame | 1 | extruded aluminum | hard anodized |
| 2 | Side plugs | 2 | cast aluminum | |
| 3 | Gear | 1 | stainless steel | nickel plated |
| 4 | Piston | 2 | steel/aluminum | oxidation/galvanic zinc plating |
| 5 | Plugs | 8 | stainless steel | |
| 6 | Piston ring | 2 | NBR | |
| 7 | Springs | 0-12 | spring steel | epoxy coating |
| 8 | Piston bearing | 2 | engineering plastic | |
| 9 | Piston ring | 2 | NBR | |
| 10 | Plug | 2 | NBR | |
| 11 | Thrust ring | 2 | engineering plastic | |
| 12 | Ring | 1 | engineering plastic | |
| 13 | Washer | 1 | stainless steel | |
| 14 | Spring clamp | 2 | stainless steel | |
| 15 | Indicator | 1 | plastic | |
| 16 | Indicator housing | 1 | plastic | |
| 17 | Bearing | 1 | engineering plastic | |
| 18 | Cam | 1 | steel | oxidation/galvanic zinc plating |
| 19 | Bearing | 1 | NBR | |
| 20 | Bearing | 1 | engineering plastic | |
| 21 | Bearing | 1 | engineering plastic | |
| 22 | Sealing ring | 2 | NBR | |
| 23 | Sealing ring | 2 | NBR | |
| 24 | Bearing | 2 | stainless steel | |
| 25 | Adjusting nut | 2 | stainless steel | |
| 26 | Adjustment screw | 2 | stainless steel | |
| 27 | Sleeve | 2 | aluminum |
Pneumatic distributor DNOVA
Technical parameters of the pneumatic distributor DNOVA
| Name | Meaning |
| Type of pneumatic distributor | spool valve |
| Working pressure, bar | 1.5 ÷ 8 |
| Supply voltage, V | 220 V |
| Full power, Va | 4.5 |
| Control | two-way electromagnetic |
| Response frequency, cycles/sec | 5 |
Sketch of the dimensions and sizes of the pneumatic distributor DNOVA
Dimensions and sizes of the pneumatic distributor DNOVA:
| Model of pneumatic distributor | 4V320-08 |
| A, mm | 71.9 |
| B, mm | 45 |
| C, mm | 94.4 |
| D, mm | 27 |
| E, mm | 69 |
| F, mm | 40 |
| I, mm | 24 |
| K, mm | 40 |
| L, mm | 188.8 |
| M, mm | 69.4 |
| N, mm | 50 |
| O, mm | 82.4 |
| P, mm | 24 |
| S, mm | 20 |
| T, mm | 6.5 |
| U, mm | 2.4 |
| V, mm | 4 |
| H, mm | 82.4 |
Manual backup DNOVA
Technical parameters of the manual backup DNOVA
| Name | Meaning |
| Climate performance | U, UHL, T, OM |
| Installation method | horizontal/vertical |
| Degree of protection, IP | 67 |
| Connection type | ISO 5211 |
Sketch of dimensions and sizes of manual backup DNOVA
Dimensions and sizes of the manual backup DNOVA:
| Manual backup model | HDM-1 |
| b1, mm | 14 |
| N, mm | 22 |
| b2, mm | 14 |
| M, mm | 16 |
| D1, mm | 50 |
| D2, mm | 70 |
| D3, mm | 50 |
| D4, mm | 70 |
| ØC, mm | 88 |
| C, mm | 120 |
| A, mm | 90 |
| F, mm | 115 |
| Y, mm | 145 |
| 4-M1 | 4-M6 |
| 4-M2 | 4-M8 |
| 4-Ø1 | 4-Ø6.5 |
| 4-Ø2 | 4-Ø8.5 |
| E, mm | 70x70 |
| B, mm | 55 |
| S, mm | 53 |
| K, mm | 10 |
| T, mm | 145 |
Sketch of parts and materials of manual backup DNOVA
Table of parts and materials of the manual backup DNOVA:
| Item No. | Details | Material |
| 1 | Rod for mounting a pneumatic actuator | steel 45 |
| 2, 8 | Sealing ring | EPDM |
| 3 | Locking spring | spring steel |
| 4 | Top end cap | aluminum alloy |
| 5 | Screw | steel 304 |
| 6 | Fixing bracket (main rod) | steel 304 |
| 7 | Frame | aluminum alloy |
| 9 | Reducer | cast iron VCh50 |
| 10 | Transition coupling | cast iron VCh40 |
| 11 | Gearbox rod | cast iron VCh40 |
Limit Switch Block DNOVA
Technical parameters of the limit switch block DNOVA
| Name | Meaning |
| Maximum limit switch voltage, V | 250 |
| Enclosure protection rating, IP | 65 |
| Working environment temperature, °C | from -40 to +80 |
| Service life, years | 10 |
Sketch of the dimensions and sizes of the limit switch block DNOVA
Dimensions and sizes of the DNOVAu limit switch block:
| Model | H, mm | L, mm | B, mm | D, mm | D1, mm | M |
| APL-210N | 77 | 112 | 88 | 10 | 5 | 20x1.5 |
Air preparation unit DNOVA AFC2000
Technical parameters of the air preparation unit DNOVA AFC2000
| Name | Meaning |
| Working pressure, bar | 8 |
| Adjustable pressure range, bar | 0.5 ÷ 9 |
| Size of filtered particles, µm | 40 microns |
| Weight, kg | 0.395 |
Sketch of the dimensions and sizes of the air preparation unit DNOVA AFC2000
Dimensions and sizes of the air preparation unit DNOVA AFC2000:
| Model ATU | AFC2000 |
| A, mm | 162 |
| B, mm | 88 |
| C, mm | 139 |
| D, mm | 31 |
| E, mm | 53.5 |
| F, mm | 12 |
| G, mm | 8 |
| H, mm | 7 |
| I, mm | 13.3 |
| J, mm | 39 |
| K, mm | 5 |
| L, mm | 40 |
| M, mm | 32 |
| N, mm | 53 |
| O, mm | 29 |
| P, mm | 6 |
| R, mm | 41.5 |
Passports and certificates
Data sheet for DNOVA DA/SA double-acting pneumatic actuator with return springs
Passports and certificates
Data sheet for DNOVA DA/SA double-acting pneumatic actuator with return springs
Specifications
Delivery
The cost and delivery time for your order depend on several factors, including the specific product you are ordering, the quantity, and the country of destination. Each product may have different manufacturing lead times and shipping requirements, which can affect the overall delivery schedule.
To get the most accurate and up-to-date information on delivery costs and timelines, we recommend contacting our sales managers. They will be happy to provide you with a detailed quote and estimated delivery time based on your specific requirements.
Please feel free to reach out to us for any questions or further assistance regarding your order.