Description
Butterfly valves DNOVA al-316l-epdm are designed for use as shut-off or regulating valves for flow control in heat and water supply systems, in technological processes of food, chemical, oil and gas, pulp and paper and other industries. Butterfly valves should be installed only between collar flanges.
Pneumatic double-acting rotary actuators and pneumatic rotary actuators with return springs are designed for automation of control process of industrial shut-off valves - gates, ball valves. DNOVA pneumatic actuators are designed for operation both indoors and outdoors. All internal and external parts are anticorrosive coated.
Pneumatic valves are used for control in pneumatic systems with NAMUR docking surface, to install the valves through holes in the housing.
Limit switch unit is designed for visual and electrical signaling of valve end positions. It is mounted on top of the pneumatic actuator surface and connected to the actuator shaft - DIN standard. The sealed box usually contains two sensors which monitor the position of the actuator shaft and signalize the end positions. Visual indication of the position can be observed on the body of the unit there is a 3D visual indicator RED-CLOSED and GREEN-OPEN.
Manual doubler with disengaging clutch DNOVA HDM allows manual adjustment of the required positioning of valves, dampers and other quarter-turn devices when replacing pneumatic, electric or hydraulic quarter-turn actuators. Suitable for both indoor and outdoor installation. The modular design of the manual doubler is designed to provide the most efficient and effective solution to the full range of manual override applications.
Technical parameters of water butterfly valve DNOVA al-316l-epdm-DNOVA-da-4m310-110/220-apl210n-hdm, body material - aluminium alloy, disk material - stainless steel AISI 316L, seal - EPDM, pneumatic actuator operated:
|
Nominal diameter DN, mm |
25–32 |
|
Operating pressure PN, bar |
16 |
|
Working medium temperature t, °C |
From -20 to +120 |
|
Working medium |
Cold and hot water, oil-free and grease-free air, other media neutral to the material |
|
Flow direction |
Two-way |
|
Body material |
Aluminum alloy |
|
Type of control |
Manual (handle) |
|
Additional option |
Electric or pneumatic actuator installation possible (ISO 5211-2001) |
|
Nominal pressure PN, MPa (kg/cm²) |
1.2 (12) |
|
Operating pressure, bar |
2...8 |
|
Working medium |
Filtered compressed air or non-aggressive gases, oils |
|
Maximum particle diameter |
Less than 30 µm² |
|
Operating temperature, °C |
-20 to +80 |
|
Adjustment range |
5° for rotation at 0° and 90° |
|
Manual duplication |
Yes |
|
Position indicator |
Open/closed |
|
Operating environment |
Indoors and outdoors (all internal and external parts are anti-corrosion coated) |
Technical characteristics of the pneumatic distributor 4M310-08 NAMUR
| Design | Spool-type |
| Test pressure (body strength test. Not for operation!), bar | 10 |
| Working pressure (recommended range for normal operation), bar | 1.5 ÷ 8 |
| Valve type | 5/2 five-port, two-position |
| Working medium | purified air (40 µm filter fineness) |
| Operating temperature, °C | 0 to +60 |
| Actuation frequency | 5 cycles per second |
| Manual override | yes |
| Protection rating/insulation class | IP65/F |
| Connection to pneumatic actuator | NAMUR-compliant mounting surface (VDI/VDE3845) |
| Body material | anodized aluminum |
| Effective cross-sectional area, mm2 | 25 (Cv = 1.4) |
| Exhaust port dimensions (vent to atmosphere) | 2 - PT1/4” |
| Air inlet port size (to pneumatic valve) | G1/4” |
| Air outlet port size (to pneumatic actuator) | 2 x Ø19.2 mm |
| Response time, sec | 0.05 |
| Supply voltage, V | 220AC/24DC |
| Coil power | 220VAC – 5.5 VA/24VDC – 4.8 W |
| Weight, kg | 0.35 |
| Average service life, cycles | 10,000,000 |
Overall and installation dimensions of the pneumatic distributor 4M310-08 NAMUR
| A | C | D | E | F | G | H | I | K | L | J | N | M |
| mm | ||||||||||||
| 40 | 24 | 28 | 32 | 40 | 21,5 | 69 | 45 | 17,5 | 135 | 29,3 | 40 | 27 |
Sketch of the dimensions of the pneumatic distributor 4M310-08 NAMUR
Basic materials and parts of the pneumatic distributor 4M310-08 NAMUR
| № | Part Name | Material |
| 1 | Connector | Engineering plastic |
| 2 | Nut | POM + carbon steel |
| 3 | Coil | Copper |
| 4 | Control Elements | — |
| 5 | Plate | Carbon steel |
| 6 | Piston | POM |
| 7 | Control Valve Seat | Engineering plastic |
| 8 | Valve Body | Aluminum alloy |
| 9 | Spool | Aluminum alloy |
| 10 | O-Ring Seal | HNBR |
| 11 | Rear Cover | Engineering plastic |
| 12 | Filter | Synthetic material |
| 13 | Piston | POM |
| 14 | Spring | Stainless steel |
| 15 | Manual Override | Engineering plastic |
| 16 | Rear Seat | Aluminum alloy |
| 17 | Spring Seat | Aluminum alloy |
| 18 | Type C Towing Shackle | 65Mn |
Sketch of the dimensions of the pneumatic distributor 4M310-08 NAMUR
Main parameters of the limit switch unit:
|
Value |
Execution |
Option |
|
Maximum current |
5 A |
- |
|
Maximum voltage |
250 V |
- |
|
Explosion protection |
No |
- |
|
Protection |
Weatherproof IP65 |
IP67 |
|
Ambient temperature |
From -40°C to +80°C |
From -50°C to +80°C |
|
Cable gland thread |
2 x NPT1/2” |
PF1/2′′, P1/2′′M20x15, PG13.5 |
|
Terminal block |
8 cells 0.08-2.6mm2 |
- |
|
Indicator position |
CLOSED: red OPEN: green |
CLOSED: red OPEN: yellow |
|
Sensor |
2 SPDT electromechanical microswitches OMRON V151-1C25 |
2 inductive sensors NPN, 2 Namur non-contact switches |
|
External coating |
Polyester coating (black) |
Red, green, yellow, blue colors |
|
Shaft |
Standard shaft (17mm) |
Extended shaft |
Main parameters of manual doublers:
| Model | Gear ratio | Torque, Nm | Weight, kg |
| HDM-1 | 26:1 | 250 | 3,0 |
| HDM-2 | 28:1 | 450 | 4,5 |
| HDM-3 | 38:1 | 700 | 6,9 |
Specifications
Delivery
The cost and delivery time for your order depend on several factors, including the specific product you are ordering, the quantity, and the country of destination. Each product may have different manufacturing lead times and shipping requirements, which can affect the overall delivery schedule.
To get the most accurate and up-to-date information on delivery costs and timelines, we recommend contacting our sales managers. They will be happy to provide you with a detailed quote and estimated delivery time based on your specific requirements.
Please feel free to reach out to us for any questions or further assistance regarding your order.