Description
The ball valve is used as a shut-off valve in heat supply systems, water supply systems, in steam, fuel and pneumatic systems with compressed air and neutral gases. Installation of valves of this series is possible in systems transporting liquid and gaseous media (water, oil, oils, steam, air, alcohols, glycol, etc.), non-aggressive to the valve materials. The use of ball valves as control valves is not allowed.
Pneumatic actuators DNOVA double-acting rotary PADA are designed to automate the process of controlling industrial valves with a maximum torque of up to 2128 Nm.
Pneumatic distributors are used for control in pneumatic systems with a NAMUR mating surface for installing distributors through through holes in the body. Electromagnetic control is carried out using voltage coils 12-AC, 12-DC, 24-AC, 24-DC, 110-AC, 220-AC. Depending on the model, distributors have one-sided or two-sided control. Pneumatic distributors with electromagnetic control have a wide range of models and include common types of switching for three (3/2) and five (5/2 and 5/3) linear pneumatic distributors. Intended for use with quarter-turn pneumatic actuators.
The manual override with worm gear and reduction gear allows manual setting of the required positioning of the shut-off element by a quarter turn, acting as an alternative to pneumatic, electric or hydraulic quarter-turn actuators. Suitable for both indoor and outdoor installation. The modular design of the manual override is intended to provide the most effective and efficient solution for the entire range of manual override tasks.
The limit switch unit is designed for visual and electrical signaling of the end positions of the shut-off element of the valve: valve, tap or butterfly valve. It is installed on top of the surface of the pneumatic drive and connected to the DIN standard drive shaft. In a sealed box, as a rule, there are two sensors that monitor the position of the drive shaft and signal in extreme positions. OMRON microswitches, inductive sensors or reed switches are used as sensors. Visual indication of the position can be seen on the body of the unit there is a 3D visual indicator RED - CLOSED and GREEN - OPEN.
The air preparation unit is designed to clean compressed air from droplet moisture and solid particles, remove condensate, automatically maintain pressure at a given level, and supply lubricant from the reservoir to the compressed air flow to the elements of the pneumatic system.
Technical parameters of DNOVA BV3232P(2pc)-FP-F-ISO-R ball valves DN200-250 PN16 full-bore flanged, body - stainless steel 316, with double-acting PA-DA pneumatic actuator, 4M310-08 220V pneumatic distributor, APL-210N LSU, MON-ISO reducer and AFC2000 ATU:
| Name | Meaning |
| Nominal pressure PN, bar | 16 |
| Working environment temperature, °C | from -29 to 150 |
| Type of crane device | two-way |
| Application | water supply, heat supply, industry |
| Working environment | water, air, neutral environments |
| Connection to the pipeline | flanged |
| Water intake | No |
| Type of flow section | full bore |
| Control type | With pneumatic drive |
| Joining | flanged |
| Control | double acting pneumatic actuator |
| Availability of limit switches | No |
| Availability of pneumatic distributor | There is |
| Availability of electropneumatic positioner | No |
| Average service life, years | 10 |
| Warranty, y. | 1 |
Sketch of the dimensions and sizes of ball valves DNOVA BV3232P(2pc)-FP-F-ISO-R DN200-250 PN16 full-bore flanged, body - stainless steel 316, with a double-acting pneumatic actuator PA-DA, pneumatic distributor 4M310-08 220V, LSU APL-210N, reducer MON-ISO and ATU AFC2000
Dimensions and sizes of ball valves DNOVA BV3232P(2pc)-FP-F-ISO-R DN200-250 PN16 full-bore flanged, body - stainless steel 316, with double-acting pneumatic actuator PA-DA, pneumatic distributor 4M310-08 220V, LSU APL-210N, reducer MON-ISO and ATU AFC2000:
| Model | DN, mm | L, mm | H, mm | ØD, mm | ØD1, mm | ØD2, mm | A, mm | E, mm | H1, mm | I, mm | B, mm | C, mm |
| DN200 | 200 | 400 | 180 | 340 | 295 | 268 | 405 | 174 | 195 | 162 | 88 | 139 |
| DN250 | 250 | 450 | 296 | 405 | 355 | 320 | 465 | 199 | 195 | 162 | 88 | 13 |
Sketch of parts and materials of ball valves DNOVA BV3232P(2pc)-FP-F-ISO-R DN200-250 PN16 full-bore flanged, body - stainless steel 316, with double-acting pneumatic actuator PA-DA, pneumatic distributor 4M310-08 220V, LSU APL-210N, reducer MON-ISO and ATU AFC2000
Table of parts and materials of ball valves DNOVA BV3232P(2pc)-FP-F-ISO-R DN200-250 PN16 full-bore flanged, body - stainless steel 316, with double-acting pneumatic actuator PA-DA, pneumatic distributor 4M310-08 220V, LSU APL-210N, reducer MON-ISO and ATU AFC2000:
| Item No. | Details | Material |
| 1 | Frame | stainless steel 316 |
| 2 | Pad | stainless steel 316+graphite |
| 3 | Lid | stainless steel 316 |
| 4 | screw | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 5 | Bolt | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 6 | Ball seal | PTFE |
| 7 | Ball | stainless steel 316 |
| 8 | Stock | stainless steel 316 |
| 9 | Thrust pad | PTFE |
| 10 | Rod seal | PTFE |
| 11 | Gland seal | stainless steel 316 |
| 12 | Bolt | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 13 | Support frame | stainless steel 304 |
| 14 | Pad | stainless steel 304 |
| 15 | Hairpin | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 16 | screw | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 17 | Shock absorbing pad | stainless steel |
| 18 | Hairpin | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 19 | screw | Stainless steel ASTM A193 Gr.B8M Cl2 |
| 20 | Gear | steel 45 |
| 22 | Screw | Stainless steel ASTM A193 Gr.B8M Cl2 |
Technical parameters of the pneumatic drive DNOVA
| Name | Meaning |
| Design | double acting |
| Control pressure, bar | 2 ÷ 8 |
| Availability of manual backup | No |
Sketch of the dimensions and sizes of the pneumatic drive DNOVA
Dimensions and sizes of pneumatic actuator DNOVA
| Drive model | DA-140 | DA-160 |
| G, mm | 25 | 30 |
| Mmm | 80 | 130 |
| N, mm | 30 | 30 |
| F0, mm | 62 | 62 |
| R, mm | 30 | 30 |
| B1, mm | 308 | 465 |
| C, mm | 67.5 | 87.5 |
| E, mm | 157 | 199 |
| J | 4-M8x12 | 4-M10x16 |
| TO | 4-M10x16 | 4-M12x20 |
| F, mm | 36 | 38 |
| A1, mm | 210 | 310 |
| D, mm | 70 | 87.5 |
| H | F10 | F10 |
| I | F12 | F12 |
| L | 22x22 | 27x27 |
Table of parts and materials of pneumatic drive DNOVA
| No. | Name | Quantity | Material | Coating |
| 1 | Frame | 1 | extruded aluminum | hard anodized |
| 2 | Side plugs | 2 | cast aluminum | |
| 3 | Gear | 1 | stainless steel | nickel plated |
| 4 | Piston | 2 | steel/aluminum | oxidation/galvanic zinc plating |
| 5 | Plugs | 8 | stainless steel | |
| 6 | Piston ring | 2 | NBR | |
| 7 | Springs | 0-12 | spring steel | epoxy coating |
| 8 | Piston bearing | 2 | engineering plastic | |
| 9 | Piston ring | 2 | NBR | |
| 10 | Plug | 2 | NBR | |
| 11 | Thrust ring | 2 | engineering plastic | |
| 12 | Ring | 1 | engineering plastic | |
| 13 | Washer | 1 | stainless steel | |
| 14 | Spring clamp | 2 | stainless steel | |
| 15 | Indicator | 1 | plastic | |
| 16 | Indicator housing | 1 | plastic | |
| 17 | Bearing | 1 | engineering plastic | |
| 18 | Cam | 1 | steel | oxidation/galvanic zinc plating |
| 19 | Bearing | 1 | NBR | |
| 20 | Bearing | 1 | engineering plastic | |
| 21 | Bearing | 1 | engineering plastic | |
| 22 | Sealing ring | 2 | NBR | |
| 23 | Sealing ring | 2 | NBR | |
| 24 | Bearing | 2 | stainless steel | |
| 25 | Adjusting nut | 2 | stainless steel | |
| 26 | Adjustment screw | 2 | stainless steel | |
| 27 | Sleeve | 2 | aluminum |
Pneumatic distributor DNOVA 4m310-08 220v
Technical parameters of the pneumatic distributor DNOVA 4m310-08 220v
| Name | Meaning |
| Type of pneumatic distributor | spool valve |
| Model of pneumatic distributor | 4m310-08 220v |
| Working pressure, bar | 1.5 ÷ 1.8 |
| Supply voltage, V | 220 V |
| Response frequency, cycles/sec | 5 |
Sketch of dimensions and sizes of pneumatic distributor DNOVA 4m310-08 220v
Dimensions and sizes of pneumatic distributor DNOVA 4m310-08 220v
| Model of pneumatic distributor | 4M310-08 |
| D, mm | 32 |
| E, mm | 69 |
| F, mm | 40 |
| I, mm | 45 |
| K, mm | 40 |
| L, mm | 134.5 |
| M, mm | 40 |
| N, mm | 24 |
| S, mm | 27 |
| U, mm | 2.4 |
| H, mm | 17.5 |
Manual backup DNOVA MON-ISO
Technical parameters of the manual backup DNOVA MON-ISO
| Name | Meaning |
| Manual backup model | MON-ISO |
| Climate performance | U, UHL, T, OM |
| Installation method | horizontal/vertical |
| Degree of protection, IP | 67 |
| Connection type | ISO 5211 |
Sketch of dimensions and sizes of manual backup DNOVA MON-ISO
Dimensions and sizes of the manual backup DNOVA MON-ISO:
| Model | MON4-1200-T54-ISO |
| b1, mm | 27 |
| N, mm | 32 |
| b2, mm | 27 |
| M, mm | 30 |
| D1, mm | Ø102 |
| 4-M1, mm | 4-M10 |
| D2, mm | Ø125 |
| 4-M2, mm | 4-M12 |
| E, mm | 129x129 |
| D3, mm | Ø125 |
| 4-Ø1, mm | 4-Ø12.5 |
| D4, mm | Ø140 |
| 4-Ø2, mm | 4-Ø16.5 |
| A, mm | 188.5 |
| B, mm | 93 |
| ØC, mm | Ø174 |
| F, mm | 202 |
| T, mm | 94 |
| Y, mm | 280 |
| H, mm | 195 |
| S, mm | 84 |
| K, mm | 15 |
| Ø steering wheel, mm | 320 |
Sketch of parts and materials of manual backup DNOVA MON-ISO
Table of parts and materials of the manual backup DNOVA MON-ISO:
| Item No. | Details | Material |
| 1 | Rod for mounting a pneumatic actuator | steel 45 |
| 2, 8 | Sealing ring | EPDM |
| 3 | Locking spring | spring steel |
| 4 | Top end cap | aluminum alloy |
| 5 | Screw | steel 304 |
| 6 | Fixing bracket (main rod) | steel 304 |
| 7 | Frame | aluminum alloy |
| 9 | Reducer | cast iron VCh50 |
| 10 | Transition coupling | cast iron VCh40 |
| 11 | Gearbox rod | cast iron VCh40 |
Limit Switch Blocks DNOVA APL-210N
Technical parameters of limit switch units DNOVA APL-210N
| Name | Meaning |
| Limit switch block model | APL-210N |
| Ambient temperature, °C | from -40 to 80 |
| Service life, years | 10 |
Sketch of dimensions and sizes of limit switch blocks DNOVA APL-210N
Dimensions and sizes of limit switch blocks DNOVA APL-210N
| Model | H, mm | L, mm | B, mm | D, mm | D1, mm | M |
| APL-210N | 77 | 112 | 88 | 10 | 5 | 20x1.5 |
Table of parts and materials of limit switch blocks DNOVA APL-210N
| Detail | Material |
| Frame | cast aluminum |
| Indicator cap | polyester plastic |
| 3D indicator | ABC plastic |
| Cam | polyester plastic |
| Spring | stainless steel |
| Screws | stainless steel |
| Sealing rings | NBR |
| Sleeve | bronze |
| Ground terminal | stainless steel |
| Shaft | stainless steel |
Air preparation unit DNOVA AFC2000
Technical parameters of the air preparation unit DNOVA AFC2000
| Name | Meaning |
| Working pressure, bar | 8 |
| Adjustable pressure range, bar | 0.5 ÷ 9 |
| Size of filtered particles, µm | 40 microns |
| Weight, kg | 0.395 |
Sketch of the dimensions and sizes of the air preparation unit DNOVA AFC2000
Dimensions and sizes of the air preparation unit DNOVA AFC2000:
| Model ATU | AFC2000 |
| A, mm | 162 |
| B, mm | 88 |
| C, mm | 139 |
| D, mm | 31 |
| E, mm | 53.5 |
| F, mm | 12 |
| G, mm | 8 |
| H, mm | 7 |
| I, mm | 13.3 |
| J, mm | 39 |
| K, mm | 5 |
| L, mm | 40 |
| M, mm | 32 |
| N, mm | 53 |
| O, mm | 29 |
| P, mm | 6 |
| R, mm | 41.5 |
Passports and certificates
Data sheet for DNOVA DA/SA double-acting pneumatic actuator with return springs
Specifications
Delivery
The cost and delivery time for your order depend on several factors, including the specific product you are ordering, the quantity, and the country of destination. Each product may have different manufacturing lead times and shipping requirements, which can affect the overall delivery schedule.
To get the most accurate and up-to-date information on delivery costs and timelines, we recommend contacting our sales managers. They will be happy to provide you with a detailed quote and estimated delivery time based on your specific requirements.
Please feel free to reach out to us for any questions or further assistance regarding your order.